STM32F10X定时器

Question

我有一个关于我的stm32f10控制器的定时器中断的问题。 当我启用状态寄存器设置为 0x1F的，因为以下标志设置定时器的计数器：UIF，CC1IF，CC2IF，CC3IF，CC4IF

这里是我做的：

#include <Compiler.h> 
#include <Debug.h> 
#include <STM32F10xxx.h> 

#include <Reset.h> 
#include "Example.h" 
#include <HW_TIM.h> 
#include <HW_NVIC.h> 
#include <HW_RCC.h> 
#include <RegBit.h> 

unsigned volatile int sr =0; 

static void SetBASEPRI(WORD const basepriVal) { 
    register WORD basepriReg __asm("basepri"); 

    basepriReg = basepriVal; 
} 

static void SetCONTROL(WORD const controlVal) { 
    register WORD controlReg __asm("control"); 

    controlReg = controlVal; 
} 

static void MainInit(void) { 
STM32F10xxx_Config(); 
SetBASEPRI(0U); 

PeripheryEnable(RCC_TIM2); 

SET_RBINDEX_REG_BIT(TIM, 2, DIER, UIE); 

SET_RBINDEX_REG_BIT(TIM, 2, DIER, CC1IE); 
SET_RBINDEX_REG_BIT(TIM, 2, DIER, CC2IE); 
SET_RBINDEX_REG_BIT(TIM, 2, DIER, CC3IE); 
SET_RBINDEX_REG_BIT(TIM, 2, DIER, CC4IE); 

InterruptEnable(NVIC_TIM2); 

SetCONTROL(1U); 
} 

void timInit(void){ 

TIM2.PSC = 0x0024; 
TIM2.ARR = 0xFFFF; 

TIM2.CCR[0] = 0x00FF; 
TIM2.CCR[1] = 0x0A00; 
TIM2.CCR[2] = 0x0F00; 
TIM2.CCR[3] = 0xF000; 

SET_RBINDEX_REG_BIT(TIM, 2, CR1, CEN); 

} 

__declspec(noreturn) int main() { 

    MainInit(); 

    timInit(); 

    while(1); 
} 

void IRQ_TIM2(void){ 
//Delet IFs in SR 
//trying to clear SR by reading the register 
sr = TIM2.SR; 
sr= GET_RBINDEX_REG_BIT(TIM,2,SR,UIF); 

//trying to clear SR by resetting the single bits 
RES_RBINDEX_REG_BIT(TIM, 2, SR, CC1IF); 
RES_RBINDEX_REG_BIT(TIM, 2, SR, CC2IF); 
RES_RBINDEX_REG_BIT(TIM, 2, SR, CC3IF); 
RES_RBINDEX_REG_BIT(TIM, 2, SR, CC4IF); 
RES_RBINDEX_REG_BIT(TIM, 2, SR, UIF); 

//trying to clear SR bei assigning 0 to SR 
TIM2.SR=0; 

} 

void IRQ_SysTick(void){ 
} 

void IRQ_HrdFault(void) { for (;;) DEBUG_BREAK(1); } 
void IRQ_UsgFault(void) { for (;;) DEBUG_BREAK(1); } 
void IRQ_BusFault(void) { for (;;) DEBUG_BREAK(1); } 
void IRQ_MemFault(void) { for (;;) DEBUG_BREAK(1); } 
void IRQ_NMI(void)  { for (;;) DEBUG_BREAK(1); } 

正如我所说的，问题在于，当计数器使能位（CEN）被置位时，所有的标志都被置位。我不能在子程序中删除它们。

Answer 1

这有点晚，但我今天面对类似的问题，我认为这可以帮助其他人。首先我怀疑问题是标志UIF，CC1IF，CC2IF，CC3IF，CC4IF是否设置。如果您查阅第403页的参考手册，其中写明这些标志由硬件设置，因此当您重置硬件时（即使在调试时仍在运行）硬件会自动设置它们，您甚至不会注意到结果。如果你想看到用调试器清除标志，我建议禁用定时器，然后执行一些操作。此外，它是检查IRQ中的中断源的推荐样式：

//comment the next line before release 
#define DEBUG  
void IRQ_TIM2(void){ 
//disable the timer for debug purpose 
#ifdef DEBUG 
    TIM2->CR1 &= ~TIM_CR1_CEN; 
#endif 
//trying to clear SR by reading the register 
if (TIM_GetITStatus(TIM2, TIM_IT_Update) != RESET) { 

    TIM_ClearITPendingBit(TIM2, TIM_IT_Update); //clearing UIF 
} 
if(TIM_GetITStatus(TIM2, TIM_IT_CC1) != RESET) { 
    TIM_ClearITPendingBit(TIM2, TIM_IT_Update); //clearing CCIF 
} 
//etc... 
//enable the timer 
#ifdef DEBUG 
    TIM2->CR1 |= TIM_CR1_CEN; 
#endif 
}